Release Date:

February 12, 2026

Enhancements:

The AV UI provides the following enhancements:

• Support for the Default profile with IGMP Plus enabled.
• Updated the Data profile to disable IGMP.
• Updated the Audio Basalte Multiroom profile to disable IGMP and MLD snooping.
• Updated the Audio Dante profile to remove storm-control for broadcast traffic.
• Updated the Lighting profile to remove storm-control for broadcast traffic.
• Updated the G&D KVM-over-IP profile and applied MAC filtering on trunk and LAG interfaces.
• Removed “cos queue strict” configuration from global QoS settings.
• Changed the default AV UI color placeholder to #00FF00 when you create a new profile.

Bug Fixes:

This firmware addresses the following bugs:

• Fixes the issue where downloading a configuration file with a non-ASCII character in port description to the switch fails. [CE-7073]
• Fixes the issue where NET-BLOCK ACL allows IGMP query packets to receive on a port and process. [CE-6990]
• Fixes the issue where SNMP traps are not sent after switch restarts. [CE-6943]
• Fixes the issue where switch is configured as the gPTP GM and advertise Clock Class capability as 255. [MS-5169]
• Fixes the issue where Savant’s AVB devices link up at 100Mb and pDelay is negative. [CE-7258]
• Fixes the issue where VLAN id is zero on the packet when the port is configured as the tagged port. [MS-5088]
• Fixes the issue where multicast entries are not remembered when MLD Plus is disabled on a VLAN. [MS-5040]
• Fixes the issue where the Rest API script is rejected if you use the Linux platform. [CE-7454]
• Fixes the issues where the Rest API token does not work after 24 hours. [CE-7418]
• Fixes the issue where the Rest API is rejected with other admin users. [CE-7351]
• Fixes the issue where the flow control does not display in the API response. [CE-7292]

Known Issues:

This AV UI contains the following known issues:

· Affected Profile: Audio Dante - Potential Network Loop on Dual-Port Dante Devices

If a Dante device with two Ethernet ports has both ports connected to the network simultaneously, a Layer 2 loop may occur, causing network instability or outage.

Workaround: Choose one of the following:

Connect only one Ethernet port per Dante device — leave the secondary/redundant port disconnected.

Manually re-enable STP on the affected interface 

Connect the Dante Primary and Secondary ports to two separate, independent networks with different VLANs, in line with Audinate’s official redundant design.

As an alternative, use Video with Audio Dante profile and toggle on PTP-TC.

This firmware contains the following known issues:

• Auto-LAG Global PTP mode in main UI configures PTP boundary clock on the newly formed Auto-LAG interface when it is enabled on the switch models that support PTP boundary clock mode. 

Workaround: Do not enable Auto-LAG Global PTP mode from main UI if you do not use the PTP boundary clock mode of operation and configure it manually on the newly formed Auto-LAG interface.

• G&D Control Center IP devices fail to link up with the switch. 

Workaround: Manually set the switch port speed to 1G to establish the link.

• This firmware includes a configuration migration process that transitions the default web browser protocol from HTTP to HTTPS. When you upgrade to this firmware and import an older configuration with HTTPS disabled, HTTPS becomes enabled. 

Workaround: Reconfigure the web browser protocol settings manually after you perform a firmware upgrade or import an older configuration

• During your initial log in, you must set up a password to access the switch. However, if you access the main UI before you set up a password and simultaneously set the password in the AV UI, the switch console might lock for up to 15 minutes. 

Workaround: Configure a password in either the main UI or the AV UI to avoid this lock up issue.

• If you upload only the private key or the certificate before you enable HTTPS, the system enables the HTTPS service but it fails to operate correctly because the configuration is incomplete. A factory reset does not fix this issue. 

Workaround: Ensure both the private key and certificate are fully uploaded before you enable HTTPS. If the issue still occurs, remove the incomplete HTTPS-related private key or certificate, and disable HTTPS before reconfiguring.

• The four 25G ports of models M4350-44M4X4V, M4350-24X4V, and M4350-24F4V can operate at either 10G or 25G speed but not simultaneously at 10G and 25G speed.
• A stacking link works only at the highest speed that the port supports. For example, if you configure a 25G port in stack mode, the port can operate only at 25G and not at 10G. Therefore, you cannot establish a stacking link if a 10G port and a 25G port are interconnected.

Warnings:

Read and follow these warnings before updating your firmware:

• HTTPS is set to default web browser protocol from firmware version 14.0.6.10 and newer versions. The default certificate is self-signed, so a browser warning might display when you log in. To avoid this warning, you can download your own certificate that is issued by a trusted Certificate Authority (CA). 

General Information:

· The boot code remains at the existing version 1.0.0.15 in this switch firmware.

· The process of upgrading the firmware and boot code takes about three minutes. Apply the “update bootcode” command from the command line interface. Do not switch off or restart the device during the upgrade process.

· AppMgr is upgraded to version 1.0.5.32 in this switch firmware.

· Insight and Engage/AV UI are mutually exclusive. This means you can only use one of these options to configure and manage the switch, not both.

· If the encrypted password in the configuration file does not adhere to the NETGEAR password policy, when the configuration file is loaded on the firmware version 14.0.6.9 or later, you must create a new password during the initial login.

Download Link: https://www.downloads.netgear.com/files/GDC/M4350/M4350_V14.0.6.17.zip

Firmware Checksum Details

File Name: M4350-v14.0.6.17.stk

MD5: 4910D82A8BAE46CE01C6AFFD4F2C8C75

SHA-256: d067f1a643b4a76279dc70258aa934a3b7b9a8c211d5edc3c5b7023f4eccdfe1

Firmware Update Instructions:

To update your product’s firmware, follow the instructions in your product’s user manual. To find your user manual, visit https://www.netgear.com/support/, enter your model number in the search box, and click the Documentation button on the product page.