GSM7328S/GSM7352S/GSM7228PS/GSM7252PS firmware version v8.0.3.25

Note: We recommend you to update your wireless drivers to the latest version available from wireless chipset vendor.

Applicable Models:

GSM7328S, GSM7352S, GSM7328FS, GSM7228PS, GSM7252PS, GSM7328S-200, GSM7352S-200

Release 8.0.3.25 Firmware

Bug Fixes from Release 8.0.3.15

1. AX743 (SFP+ adapter) does not work on GSM73xxSv1 
2. Add support to upload the crashdump file from the switch to PC.
3. "input error" will return if ‘techsupport enable’ command is entered from a non-admin user.
4. MSTP doesn’t work after setting STP Configuration name through GUI.
5. MAC port security expanded to support 4K per port.
6. Device is not returning SNMP MIB OID agentSwitchCpuProcessMemAvailable value correctly.
7. Add support for per port flow control.
8. Device fails to assign DiffServ Policy beyond 9 interfaces.
9. Device is not supporting dot3PauseTable.
10. Trap log time do not reflect time zone offset.
11. MIB object dot3OutPauseFrames not returned on stack.
12. Switch is snooping VoIP traffic and logged event to the message log even though VoIP is not enabled.
13. Switch sometime reports error about I2C operation failed for SFP.
14. Switch might reboot after connecting certain AVAYA phones and AutoVoIP is enabled, which is disabled by default.
15. Switch GUI page won't accept domain default name with numbers at the beginning.
16. ‘clock summer-time’ command is not working.

Known Bug against Release 8.0.3.25

1. DNS Host Configuration table in the GUI page does not support setting of IPv6 host address.
   Workaround: configure IPv6 host address through CLI.

Upgrade procedure

1. Save the current configuration data. Normally the firmware will preserve the original configuration in the switch, however, just in case something went wrong during the upgrade, you may want o save a copy of current running configuration. To do so, go to Maintenance->Upload page, and select Text Configuration option and click Apply button to save the configuration file.
   
   

   

2. Download the new firmware and store it in a PC. Be sure to note the file's location in the file system.
3. Upgrade the firmware.  There are two ways to load the firmware from a PC to the switch:  TFTP through the PC’s TFTP server or HTTP through a web browser. 
   
4. Upgrade using TFTP through the console copy command (Recommended)

   This requires a TFTP server to be installed on a PC that is on the same network as, and accessible to, the Switch.

   1. Copy the downloaded firmware to the TFTP root directory.
   2. Start the TFTP server.
   3. From the switch console, execute the commands as pictured below.
      Note:  Do not reboot or power cycle the switch until it has downloaded the firmware and returned to the prompt.  Doing so may render the switch unbootable.
      
      
   4. Reboot the switch once it completes downloading the firmware and returns to the EXEC prompt.
      

5. Upgrade using the Switch Web GUI

   1. Use any web browser to access the Switch management IP address.
   2. Go to the Maintenance > Download page, select HTTP File Download, and set the File Type to "Archive."
   3. If the current switch firmware is version 7.x:

      

      • Click the Apply button to start the download.  Do not power cycle or reboot until the switch completes the download and the Select File box becomes blank
      • Connect the PC's serial port to the switch console port using a DB9 cable (shipped with the switch). If your PC does not have a DB9 serial port, you'd need to get a USB to serial adapter to connect the PC to the switch's console port.
      • Start a terminal emulater on the PC such as Hyperterminal.
      • Reboot the switch and watch for the console output on the terminal emulator.
      • When the console outputs prompt you to enter boot menu, enter 2

      • 
        

      • We need to update the boot code. Select the option to update the boot code (usually it is option#8 depends on the firmware version). It should take less than a minute. Once completed, the prompt will return to [boot menu].
      • Enter command option#1 to start operation code.
      • The switch should be operational with the new firmware.
   4. If the current switch firmware is version 8.x:

      

      • Click the Apply button to start the download; a window will open to display the download progress.  There will be a new notification window once the download has successfully completed.
      • Access the command line interface of the switch using Telnet.
      • Login to the switch and enter "enable" to access the privileged mode.
      • Enter the command: update bootcode to update the switch's bootcode
      • Enter the command: reload to reboot the switch.
      • The switch should boot up with the new firmware.

After upgrading the firmware:

1. After the switch has restarted, verify the firmware version is correct.
   • From the CLI, use the command # show hardware
   • From the GUI, go to the System main page
2. Verify the switch running configuration by issuing the “show running-config change” command. The output should match the configuration file saved on step #1. If not, please call NETGEAR customer support and manually reapply the missing configuration commands back to the switch.
3. You can now make additional configuration change for your application need. And be sure to use "save" command to save the configuration after you're done.
4. If a stack of switches is being upgraded, each switch should automatically upgrade.  However, if the switch stack cannot boot up after the upgrade, try upgrading each individual switch before rebooting the stack.
5. If an older image (predating the upgrade) appears after rebooting, it may be the backup image if your previous version supported dual image.  To resolve this:
   • Determine the what image the switch is using:
     #show bootvar
     The output will indicate which image is in use; if it is image2, the newly loaded image should be image1.
     
   • Activate the new image:
     #boot system image1
     
   • Reboot the system.
6. In rare instance, after upgrading from a pre-8.0 release, the switch may stop at the boot menu during boot up:
   

   If this occurred, select menu option#11 to restore the configuration to factory default. Then, select option#1 to start the operational code. If this still do allow the switch to completely booted up, contact Netgear technical support for assistance.

Document Type

This product includes software code developed by third parties, including software code subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL Code and LGPL Code used in this product, are available to you at NETGEAR's Open Source Code Web page. The GPL Code and LGPL Code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more authors. For details, see the GPL Code and LGPL Code for this product and the terms of the GPL and LGPL.