FSM7326P Firmware Version 6.1.0.9

FSM7326P Firmware Version 6.1.0.9

Published May 25, 2007

New Features/Enhancements/Bug Fixes:

1. Port description feature to allow description be added to each port
2. Add support for new switch model GSM7328FS
3. Add “show mac-addr-table <vlan id>” command that shows mac addresses learned per VLAN
4. The “show mac-addr-table” command now supports '<mac-addr>' option without requiring <vlan id> option
5. Add “configure terminal” command which works the same as “configure” command
6. Logical Interface name (e.g. “vlan <id>”, “lag <id>”) display changes missing in some CLI commands.
7. SNMP MIB objects, etherStatsOversizePkts, etherStatsJabbers, SyRmSnRmEs, are not functioning properly.
8. Port Config pop menu fails in JRE 1.6.0
9. GSM73xxS: IGMP snooping not working
10. Configuration script file could not be executed completely with certain configuration
11. DHCP server client config show run output has bad client-identifier
12. Rebooting when building 200 neighbors and receiving 2 routes from each neighbor
13. GSM73xxS: Fan Status always reported as OK in show hardware output
14. FSM73xxS: Diffserv Class with matching condition mac address and mask is not working.
15. DHCP client: switch crashes while obtaining address from server
16. SNMP SET operation not being done properly on the object - 'agentStpConfigRevision'
17. RIP: wrong route will be sent when changing its subnet mask frequently
18. GSM73xxS: 10G fiber ports showed media type as copper
19. GSM73xxS crashes when enable/disable OSPF on the remote end more than 2 times
20. SNMP: configuration script contains SNMP setup would fail to apply
21. FSM7328S crash with banner file download
22. SNMP: command 'no snmp-server community ipmask 255.0.255.0' failed
23. SNMP: command line inconsistent with running-config
24. port-channel static should be configured in "interface lag <lagid>" mode 
    

Known Issues:

1. OSPF specific routes can not be advertised after summary routes are deleted
2. Routes can not be summarized after shutdown/ no shutdown the link

Upgrading

Note: Version 6.1.0.9 will support configuration migration from all previous to this version. However, if user decides to revert back to the version 5.x or older, the configuration will be lost. If the current version is 5.x, please save a copy of your current configuration in case you want to revert back to 5.x. Version 6.0 configuration will be interchangeable with 6.1.

1. Using the button below, download the firmware file. You do NOT have to unzip this file.
2. If you have not setup any special functions on the existing switch other than the management IP address, or you have saved a copy of the configuration in a text file, proceed to the next step.
   • On the existing switch, use capture mode in Hyperterminal to capture the output from the switch console to a file.
   • On the switch console, type “show run”. The output of current running configuration will be captured in the file.
   • Open the file and review the content. If there is any changes to the configuration but not present in the file, manually add them. Save the file after it is done.
3. Start a tftp server on the PC where the new images are stored. If you do not have a tftp server, you may want to try either of the following public domain tftp servers: 
   PumpKIN - http://kin.klever.net/pumpkin/ 
   Solarwind - http://support.solarwinds.net/updates/New-customerFree.cfm
4. On the switch console, type the following command:
   • # copy tftp://<tftp server IP address><image name> system:image
   • It will ask for confirm with input data displayed. Hit enter if all parameters look correct.
   • The download should take a minute or two, after that, the code will be checked for possible corruption, if not, it will report firmware successfully upgraded.
   • Reboot the switch by typing “reload” command or power cycle the switch.
5. After the switch is restarted, type the following command to verify the version is correct.
   • # show hardware
6. .If you did not skip step #1, now you can use the saved “show run” output file to restore the switch to your configuration, otherwise skip this step.
   • First enter exec mode, by enable command after you logged in.
   • Once in exec mode, paste the content of that file to the console. If there is any error during such operation, please report it to NETGEAR tech support.
   • Do a “show run” command on the console and make sure everything you expect to be there is present. If not, please report the problem to the tech support and manually add your configuration back.
7. You can now make additional configuration change for your application need. And be sure to use “copy” command to save the configuration after you’re done.

Downloads > Driver/Software/Firmware